How I Fit a Cable to a Border



Yesterday I posted this picture on Instagram showing how I fit a cable on a border and make it wrap around corners evenly.  This has been a question I've been asked repeatedly ever since I posted about machine quilting cables on a home sewing machine.  I thought I would share it with you while it's fresh in my mind, but keep in mind, there is math involved!  It also requires software that allows you to resize an image.  I use Adobe Photoshop.

First, I measure my borders to get precise dimensions.  You need to measure at the seam line where the border is sewn to the quilt, not along the outermost edge of the border.  I never use a plastic tape measure, they are not accurate.  I use the metal type you find in any hardware store.  I place the one-inch measurement on the very corner of the seam line, measure across, then subtract one-inch from the final dimension.  The quilt I am working on measured 42 7/8" by 59 7/16" and I converted these dimensions to decimals--42.875" by 59.4375".

I have a large variety of cable quilt stencils, but rarely do they ever fit the border of a quilt perfectly unless I design a quilt specifically to fit a stencil repeat.  In addition, none were wide enough for this border, which is 7 inches.  I also knew that I wanted the repeats to work out evenly on all four sides so that the cable would wrap each corner.  This meant I had to find a common fraction for the repeat size that would work with both border measurements and would divide evenly.  So rather than get into overly complicated math (from high school classes that I have no memory of!),  I take each border dimension and divide it by 4, 5, 6 and 7 (or whatever numbers are appropriate for the size quilt I am working on) until I get a size that is as close possible for both border dimensions:

You can see that approximately 8.5" is the closest measurement each side shares.  To get a bit more precise, I subtract the difference between the two and then divide by 2:  8.575 - 8.491 = .084, then .084 ➗ 2 = .042.  I subtract the .042 and add .042 as follows:  8.575 - .042 = 8.533 and 8.491 + .042 = 8.533.  This gives me the final measurement of the cable repeat I will need--8.533", knowing that the shorter borders will have five total repeats and the long borders will have seven total repeats.  I also know that I will have to fudge the cables a little to make the repeats meet the corners precisely, due to the slight differences in measurement for the cable repeat for each size border, but I do that as I am drawing them onto the quilt and once they are quilted, it looks seamless.



Next I scan the cable stencil in my scanner with a black piece of cardboard on top of it so that the lines will scan black when I open the image file in Photoshop.  It is critical to lay the stencil as straight as possible on the scanning bed.  I am only concerned with scanning the repeat, not the corner part, at this point.  I use the cropping tool in my scanning software to select the repeat as precisely as I can, scan, and then save the file as a .jpg image.  I then open the file in Photoshop and make sure that the repeat is precisely selected with the Marquee tool, deleting any excess area outside of the cable lines, and crop if necessary.  Then I change the dimensions of the image under the menu Image→Image Size, making sure the Constrain Proportions box is unchecked, and type in the size I want.  In this case I wanted the Document Size to be 7" wide (cable width) and 8.533" (length of repeat) inches high.  I set the Resolution Size to 300 pixels per inch.  I also adjust the brightness and contrast of the image in Image→Adjustments→Brightness/Contrast by setting the brightness and contrast settings to the far right until the background of the image is bright white and the lines are dark black.   After I save the new image, I can print as many repeats as I need, cutting and taping them together to fit the border.  This is where I double-check my math and fudge repeats to fit as necessary if needed.



Next I repeat the same process for the corner cable, selecting just the corner part of the stencil and following the same steps as I did for the repeat, above.  The only difference is, since this is a corner, I want it perfectly square, not rectangular like the repeat above.  Holding down the Shift key while selecting the image will keep the bounding box perfectly square.  For this corner cable, I set the Document Size at 7" by 7" (which is the width of cable itself). 

I print and tape this to one end of the length of the cable.  I now have a complete master of my cable which I trace onto the quilt using a light table and my blue soluble markers.

Hope this gives you a better idea on how to fit cables to your borders.  It sounds complicated, but once you do it, you will be so happy that you can actually make a cable wrap around four corners of a quilt and have it look seamless!  Happy Quilting!

Finished. . .Finally!

Well, my Ocean Waves quilt is finally finished and I am really happy with how it turned out and ready to move on! 

I still have lots to do as far as decorating/re-decorating our bedroom goes, but this quilt was probably the most labor intensive part of the project, so now I feel like I can officially BEGIN with the rest of my to-do list now that this is done.  I started this quilt in mid-December and have put off so many other things these last few months in order to stay focused on this quilt.  But now I am really ready to play catch up, including a major spring cleaning of our house.

I did get my Bernina 710 back in time to finish the quilt.  I had probably done about 80% of the quilting with my old 440 and it worked great through the entire process.  But having the 710 and the extra space under the arm made a world of difference!  I could easily quilt the feathered wreaths in the center of the quilt without cramming the rest of the quilt under the machine.  It was wonderful!  And between free-motion quilting and straight line quilting with the walking foot, I had no issues with the Invisafil thread shredding this time around.  Hooray! 

For those of you that are curious, the upper thread is Invisafil (100% polyester, 100 weight, very fine) and the bobbin thread is Mettler Metrosene (100% polyester, fine).   The batting is Hobb's Heirloom 80% cotton/20% polyester.  I use this batting predominately because I really like a flat, crinkled, vintage look.  I did wash the quilt prior to binding it.  I know many quilters have made the transition over to the wool battings but I have yet to do so.  Something about wool in Florida just doesn't sound appealing to me!  But I do think the quilts that are quilted with the wool battings are just spectacular and I will probably eventually try one just to see if I like it.

All the straight lines, the two cable borders, and the straight lines behind the large feathered border were done with a walking foot.  The feathered wreaths in the white squares and feathered border were all free-motioned.  I did use the Schmetz #75/11 quilting needle and I did slow down my quilting speed.  I also lowered my tension even more than what my dealer suggested.  Part of the reason for this is that I used a pale pink thread in the bobbin to match the backing and with the tension set at 3.0, I could see little pink dots of thread coming to the top of the quilt in the holes the needle left behind.  So for free-motion quilting I set the tension down to 2.0 and for walking foot quilting, I set the tension at 2.25.  The stitch quality looks fine on both the front and back and this eliminated any bobbin thread from showing on the top side.  I did not have a single thread breakage!  Back to being a happy quilter!

And I just want to thank those of you that cheered me on for my perseverance!  I appreciate the support!  I'm sure you've all been in a situation at least once where you keep asking yourself, why the heck am I going to so much trouble and aggravation??  But the extra effort is generally worth it in the end and I will admit that I really am happy with the way this turned out.

And one last thank you. . . .I LOVE all of the comments and e-mails you all are sending me and I am just so overwhelmed at the response I've gotten from all of you!  I know I don't blog nearly as often as many popular bloggers do, but I really do appreciate your loyalty and sticking around in spite of that.  You really have no idea how broad of an audience you have when you blog, there are stats you can check to see how many hits a post gets, but as far as readership, I am truly clueless as to how big of an audience I have.  Sometimes I wish I could take a roll call!  But it is just so reassuring to have real live feedback from you and it lets me know that I am not just writing to some void in outer space!  So again, thank you from the bottom of my heart for reading, commenting, and for your support!  Hugs to all of you! 

I may be gone for a bit longer between posts since I have tons to catch up on, but don't worry, I will update you as soon as I have something to show you again.  Happy Quilting. . .

Quilting Frustrations

Happy March to everyone!  I am STILL working on quilting this Ocean Waves quilt but I am finally seeing the light at the end of the tunnel.  I'm sure you are all sick of hearing about it, too!  I really hope to be finished with it by the end of this week if all goes according to plan.

Speaking of which, the original plan I had for this was to quilt it with my new Bernina 710 and really put the machine to the test.  I bought this machine last fall mainly for one reason and that is for the extra room under the arm to the right of the needle.  It has about a 10+ inch span, versus 7-7 1/2 inches on a regular machine, like my old Bernina 440.  Since I don't see a longarm machine in my future, this was supposed to appease me for the time being.  The quilt I'm working on is a king size and was going to be the perfect way for me to test the new machine and practice free-motion quilting on such a large scale.  Well, my plan didn't work out as I had hoped!




Bernina 710

Bernina 440

I started out with the walking foot and quilted in the ditch and straight lines in the body of the quilt.  After about an hour into quilting, the Invisafil thread that I use for quilting kept shredding.  I've used this thread by Wonderfil for eight or more years and have never, ever had issues with it previously in my 440.  However, I have heard from a couple of you and also read on various blogs where many people cannot sew with Invisafil on their machines and the 710 popped up repeatedly in these discussions.  I couldn't understand why!  I e-mailed my Bernina dealer several times to see if we could come up with a solution.  One was to switch to a different needle, a Schmetz 75 quilting needle.  This helped a little bit at first.  I also lowered the tension to about a 3 and at some point, even down to 2.75.  But once again, I began having issues and I couldn't go longer than 15 or 20 minutes without the thread shredding.  Frustration and several favorite expletives took hold and at that point, I decided to give up.  I put the old faithful 440 in its place and took the 710 to my dealer, where it still is today.

In the mean time, after finishing up all of my straight lines with the walking foot, I began to notice that all the areas where I had used the blue pounce powder with the feather stencils had almost faded away to nothing!  I was not a happy quilter!  I guess due to the time that had lapsed and so much handling of the quilt, it just didn't hold up like I had thought it would.  So I had to go back and spend two days remarking all the feathered wreaths and border with a blue water soluble pen.

In the mean time, my Bernina dealer called me and said my 710 is fixed and ready to pick up.  He replaced the thread guide on the needle clamp because the old thread guide wouldn't hold the thread in place.  He also did a lot of sewing with Invisafil, getting the same results I was.  He spoke with the Bernina people and they told him a lot of this issue is due to the rotary hook feature in the bobbin.  I don't know the technical reason why the thread shreds because of this, something with the way the needle goes down into the bobbin, I think.  But he said to use the #75 quilting needle, a lower tension, around a 3, and to sew at half speed.  He said once he did that, he didn't have the shredding issues.  So we will see, I am anxious to see if that makes a difference once I quilt on it again.

So I am still chugging along on the 440, fighting with perfecting my free-motion skills in a tight little space on a huge quilt.  Challenging doesn't begin to cover it!  All I can think about is how those amazing women whose work I admire, like Diane Gaudynski and Sue Nickels, can do such incredible show-stopping quilting on a home machine and stick with it for such a long period of time on one single quilt.  You don't realize the amount of mental concentration and physical ability it requires until you are actually doing it yourself.  It ain't easy!  But I will be sooooooo happy when this is done and I cannot wait to show you the results after the quilt is washed. 

Hopefully I will have more pictures of my quilt to show next time around.  Happy Quilting!